Fault codes Miele Washing Machine

A fault with your Miele washing machine always comes at an inconvenient time. Often, the appliance indicates what is wrong on the display with a specific error code (such as F20 or F50). But what do these messages mean exactly? In the overview below, we have gathered all Miele washing machine error codes for you. Discover the cause of the fault immediately and use our handy tips to resolve the issue yourself, where possible. Can't clear the error message? Our experienced technicians are ready to assist you.

Miele Washing Machine Error Codes

What is code F1 on a Miele washing machine?

Short circuit in the power circuit of the temperature sensor heating/water.

You probably cannot resolve this quickly and safely yourself.

What is code F2 on a Miele washing machine?

Fault in the power circuit of the temperature sensor heating/water.

You probably cannot resolve this quickly and safely yourself.

What is code F3 on a Miele washing machine?

Short circuit in the power circuit of the temperature sensor heating register.

You probably cannot resolve this quickly and safely yourself.

What is the F4 code on a Miele washing machine?

Power failure temperature sensor heating register.

You probably cannot resolve this quickly and safely yourself.

What is the F10 code on a Miele washing machine?

The water supply is blocked or obstructed.

• The tap is not turned on.
• The filter in the water supply (plastic block on the supply arm) is contaminated.
• The water supply hose is kinked.

What is the F11 code on a Miele washing machine?

The water is not draining properly.

The end of the drain hose is too high. Check that the maximum lift height of 1 m is not exceeded.

Remove kinks or loops from the drain hose.

Clean the lint filter and the drain pump:

• Turn off the washing machine.
• Open the flap for the drain pump (bottom left).
• Place a container or bowl under the flap, e.g. a universal baking tray.
• Loosen the filters until water flows out of the appliance.
• Tighten the lint filters again to interrupt the water drainage.
• If no more water is flowing out: completely unscrew the lint filters.
• Thoroughly clean the filters.
• Check if the pump blades can turn easily. Remove any foreign objects (buttons, coins, etc.) if necessary and clean the inside.
• Reinsert the lint filters. Ensure that the lint filters are placed on the correct side.
• Tighten the fluff filters properly so that no water can leak afterwards.
• Close the flap for the drain pump.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F15 on a Miele washing machine?

The water supply is blocked or obstructed.

• The tap is not turned on.
• The filter in the water supply (plastic block on the supply arm) is contaminated. You can unscrew and clean this yourself.
• The water supply hose is kinked.

What is the code F16 on a Miele washing machine?

Too much detergent or washing aid, such as stain remover, has been dosed.

• Dose less detergent (aids).
• Incorrect wash programme selected for this laundry. Choose the wash programme that is suitable for this laundry.
• Foaming due to overdosing of the detergent. Pay attention to the dosing advice from the detergent manufacturer corresponding to the water hardness and soiling of the laundry.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F19 on a Miele washing machine?

The flow meter is not working properly.

You probably cannot resolve this quickly and safely yourself. Book a repair with We.repair.

Wat is de code F20 of Storing verwarming op een Miele wasmachine?

The display of the washing machine/wash and dry combination shows the fault F20 or Heating fault.

The thermostop has been activated. The Thermostop function ensures that the temperature set for the programme is reached. The thermostop starts if the set temperature is not reached within the specified time. When the thermostop is activated, the remaining time indication stops.

Once the set temperature is reached, the washing programme continues and the remaining time indication resumes.

The heating has a fault.

• Disconnect the washing machine/wash and dry combination from the electricity supply. Unplug it from the socket or switch off the main switch.
• Wait at least 2 minutes before reconnecting the washing machine to the electricity supply.
• Turn the washing machine back on.
• Restart the programme.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the F29 code on a Miele washing machine?

The steam generator has a fault.

You probably cannot resolve this quickly and safely yourself. Book a repair with We.repair.

Wat is the code "F34, Door lock, call Customer Service" on  Miele washing machine?

The drum is overloaded. Observe the maximum load, which is described in the user manual. Switch the appliance off and then on again.

There may still be a technical fault.

• Make the washing machine voltage-free.
• Unplug it from the socket or switch off the main switch.
• Wait at least 2 minutes before reconnecting the washing machine to the electricity supply.
• Turn the washing machine back on.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

Wat is the code "F35, Door release, call Customer Service" on a Miele wasmachine?

Technical fault.

You probably cannot resolve this quickly and safely yourself. Book a repair with We.repair.

What is the code F37 on a Miele washing machine?

Check if the washing machine is level. You can find more information in the user manual.

The drain hose is connected too high. The maximum lift height is 1 m.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F39 on a Miele washing machine?

The electronics have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F41 on a Miele washing machine?

The electronics have a fault.

Possible solution: turn off the washing machine and turn it back on after about 10 seconds.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F43 on a Miele washing machine?

The electronics have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F44 on a Miele washing machine?

The electronics have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F45 on a Miele washing machine?

The electronics have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F47 on a Miele washing machine?

The electronics have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F49 on a Miele washing machine?

The electronics have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F50 on a Miele washing machine?

The drum drive has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F51 on a Miele washing machine?

The pressure sensor has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F53 on a Miele washing machine?

The drum drive has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F56 on a Miele washing machine?

The spin speed during the last spin was lower than 400 revolutions per minute.

Foaming due to overdosing of the detergent. Pay attention to the dosing advice from the detergent manufacturer according to the water hardness and the soiling of the laundry.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F62 on a Miele washing machine?

Technical fault. The programme selector switch is between two settings.

Turn the programme selector switch to a defined setting.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F63 on a Miele washing machine?

The water exchanger has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F64 on a Miele washing machine?

The magnetic field sensor has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F65 on a Miele washing machine?

The drum lighting has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F81 on a Miele washing machine?

The steam generator has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F83 on a Miele washing machine?

The steam generator has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F92 on a Miele washing machine?

If washing is done continuously at low temperatures, this can lead to germ formation in the washing machine.

Solution: run a programme at a temperature of at least 60 °C.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F103 on a Miele washing machine?

The Mbus module has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F104 on a Miele washing machine?

The drum drive has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F105 on a Miele washing machine?

The steam generator has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F106 on a Miele washing machine?

The steam generator has a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F130 on a Miele washing machine?

The electronics have a fault.

What is the code F131 on a Miele washing machine?

The electronics of the external dosing unit have a fault.

You probably cannot resolve this quickly and safely yourself.

What is the code F138 on a Miele washing machine?

Technical fault. There is water in the drip tray.

Turn off the water supply tap to prevent further damage.

You probably cannot resolve this quickly and safely yourself.

What is the code F139 on a Miele washing machine?

Technical fault. There is water in the housing of the external dosing unit.

Turn off the water supply tap to prevent further damage.

You probably cannot resolve this quickly and safely yourself.

What is the code F140 on a Miele washing machine?

Technical fault. The water level in the supply reservoir of the external dosing unit is too high.

You probably cannot resolve this quickly and safely yourself.

What is the code F199 on a Miele washing machine?

Fault in the connection between the washing machine and the XCI box.

You probably cannot resolve this quickly and safely yourself.

What is the code F210 on a Miele washing machine?

The PowerWash has a fault.

The injector at the top of the door seal may be blocked. Carefully remove any lint with your fingers.

Clean the lint filter and the drain pump:

• Turn off the washing machine.
• Open the flap for the drain pump (bottom left).
• Place a container or bowl under the flap, e.g. a universal baking tray.
• Loosen the filters until water flows out of the appliance.
• Tighten the lint filters again to interrupt the water drainage.
• If no more water is flowing out: completely unscrew the lint filters.
• Thoroughly clean the filters.
• Check if the pump blades can turn easily. Remove any foreign objects (buttons, coins, etc.) if necessary and clean the inside.
• Reinsert the lint filters. Ensure that the lint filters are placed on the correct side.
• Tighten the fluff filters properly so that no water can leak afterwards.
• Close the flap for the drain pump.

Neem contact op met We.repair als de storing blijft optreden of boek direct online een reparatie-afspraak.

What is the code F211 on a Miele washing machine?

Technical fault. Short circuit in the TwinDos sensor of the thermo-element reservoir 1.

What is the code F212 on a Miele washing machine?

Technical fault. Power failure in the TwinDos sensor of the thermo-element reservoir 1.

What is the code F213 on a Miele washing machine?

Technical fault. Short circuit in the TwinDos sensor of the thermo-element reservoir 2.

What is the code F214 on a Miele washing machine?

Technical fault: power failure in the TwinDos sensor of the thermo-element reservoir 2.

What is the code F220 on a Miele washing machine?

The washing machine may be leaking.

• Contact We.repair if the fault persists or book a repair appointment online directly.

This fault may appear without reason and the washing machine may not be leaking.

• Make the washing machine voltage-free.
• Check if water has leaked from the washing machine.
• If no water has leaked, reconnect the washing machine to the electricity supply.
• Start a random wash programme.
• If the washing machine is functioning normally and no fault is reported, F220 has appeared without reason. You can continue to use the washing machine.

• Check if the machine is connected to your WiFi. A software update is available.

  • If your washing machine is not suitable for network connection, please contact We.repair.

What is the code F242 on a Miele washing machine?

Technical fault. Communication failure between the touchscreen and electronics.

Contact We.repair if the fault persists or book a repair appointment online.

What is de code "< 25 % load" when the drum is full of a Miele washing machine?

When switching off the washing machine, there was laundry in the drum. The load is displayed in %. The minimum value it can show is < 25 %.
This has changed the zero point and the device may indicate a load of less than 25% (the minimum).

Reset the zero point, see the user manual.

To prevent changing the zero point in the future:

Switch on the washing machine before filling the drum.

Switch on the washing machine before emptying the drum.

Completely empty the drum after a programme.

Vul geen water bij via de wasmiddellade."

What is the code "< 25%" when the drum is empty of a Miele washing machine?

This is not a fault.

< 25 % is shown on the display of the washing machine/washer-dryer when the drum is empty. The load is displayed in %. The minimum value it can show is < 25 %.

What is the code -0- on the display of a Miele washing machine?

-0- is shown on the washing machine display. This indicates that the position of the programme selector was changed after starting the programme. After the start of a wash programme it is no longer possible to select a different programme.

The position of the programme selector has been changed while the appliance was running.
Turn the programme selector back to the previously started programme.
The programme time is shown on the display.
If you want to cancel the programme, proceed as follows:
If you have the Start/Add laundry sensor control, turn the programme selector to the  position and then to any other position.
If you do not have the Start/Add laundry sensor control, touch and hold the Start/Stop sensor control until the time display switches to :.
Rotating bars  ...  ... , the -0- symbol or the  symbol are shown on the display.
The water is pumped away and the door lock is then released.
Open the door.
Close the door.
Turn the programme selector to the required programme.
Start the programme.

Select the previously started programme with the programme selector switch. The time of the programme will be displayed.

​

• ​
• Als u de sensortoets Start/Trommel bijvullenniet heeft, raakt u de sensortoets Start/Stop net zolang aan tot de tijdsaanduiding op : springt.
• In the display, rotating dashes  ...  ... , the symbol -0- or the symbol  appear.
• The water is pumped out and then the door lock is deactivated.
• Open the door.
• Close the door.
• Turn the programme selection switch to the desired programme.
• ​

What is the code 888 on the display of a Miele washing machine?

The programme does not start.

Deactivate the demo mode.

Deactivate demo mode on washing machines with the On/Off button:

• Turn off the washing machine.
• Close the door.
• Press and hold the sensor button Start/Stop.
• Turn on the washing machine while holding the sensor button Start/Stop.
• The sensor button Start/Stop is flashing.
• After 5 seconds, the sensor button Start/Stop lights up continuously.
• Release the sensor button Start/Stop briefly.
• Touch the sensor button Start/Stop again and hold it for 3 seconds.
• The sensor button Start/Stop is no longer lit.
• The demo mode has been deactivated.

Deactivate demo mode on washing machines without an On/Off button:

• Turn on the washing machine.
• Open the door.
• Press and hold the sensor button Start/Stop.
• Close the door while holding the sensor button Start/Stop.
• After 5 seconds, the sensor button Start/Stop lights up continuously.
• Release the sensor button Start/Stop briefly.
• Touch the sensor button Start/Stop again and hold it for 3 seconds.
• The sensor button Start/Stop is no longer lit.
• The demo mode has been deactivated.

Wat is de code ADD in het display van een Miele wasmachine?

This is not a fault.

ADD indicates that the door can be opened to add or remove laundry. If you do not want to add laundry to the drum, you do not need to do anything.

If you want to add laundry to the drum, you need to do the following:

• Open the door.
• Place laundry in the drum or take laundry out.
• Close the door.
• Touch the sensor button Start/Drum fill.
• Operation blocked "Child lock is active.
• Deactivate the child lock.
• More information can be found in the user manual.

Wat is de code Controleer dosering van een Miele wasmachine?

Too much detergent has been dosed.

Follow the dosing advice on the packaging.

Follow the instructions in the washing machine's user manual.

Take water hardness into account.

Take the degree of soiling into account.

Dose gradually less detergent.

Check the dosing settings on washing machines with automatic detergent dosing.

Wat betekent het als Controlelampje Afvoer knippert van een Miele wasmachine?

The water is not draining properly.

The end of the drain hose is too high. The maximum lift height is 1 m.

Check that the maximum lift height of 1 m is not exceeded.

The lint filter and the drain pump are clogged. Clean the lint filter and the drain pump. More information can be found in the user manual.

Wat betekent het als Controlelampje Toevoer controleren knippert van een Miele wasmachine?

The water supply is blocked or obstructed.

• The tap is not turned on. End the wash programme. Turn on the tap. Select the programme and start it again.
• The filter in the water supply is contaminated. Clean the water supply filter in the plastic block on the supply hose. More information can be found in the user manual.
• Remove kinks or loops from the water supply hose.

There may still be a technical fault. Book a repair with We.repair.

Wat betekent het als Controlelampje Vergrendeld brandt van een Miele wasmachine?

The lock has been activated.

Deactivate the lock as follows: press the Start button until the Locked indicator light goes out.

OR

If the Crease Protection/End indicator light is flashing: set the originally selected programme and press the Start button until the Locked indicator light goes out.

Wat betekent het als Controlelampje i brandt met een 1 op een Miele wasmachine?

The indicator light i is on the washing machine and 1 appears in the display's time indicator.

No wash programme with a temperature of more than 60 °C has been run for some time.

Start the Cotton 90 °C programme with the Miele machine cleaner or a universal powder detergent.

The washing machine is being cleaned and no germs or odours are formed.

Wat betekent het als Controlelampje i brandt met een 2 op een Miele wasmachine?

The indicator light i is on the washing machine and 2 appears in the display's time indicator.

TwinDos has not been used for too long. There is a risk that the detergent in the hoses will dry out.

Immediately clean the TwinDos system (see chapter: “Cleaning and maintenance”, section: “TwinDos maintenance”).

What does it mean if the "Crease Protection/End" indicator light is flashing and the "Locked" indicator light is on a Miele washing machine?

On the washing machine/wash-dry combination, the indicator light for Crease Protection/End is flashing and the Locked indicator light is on.

The selected programme setting has changed when the lock was activated.

Press the Start button until the Locked indicator light goes out.

OR

If the Crease Protection/End indicator light is flashing: set the originally selected programme and press the Start button until the Locked indicator light goes out.

Wat is de code Ctr in de display van een Miele wasmachine?

Ctr appears on the display of the washing machine.

The Remote Control function is activated.

If the Remote Control function is activated (programming mode P98, programming option 01), Ctr appears at the start of a programme.

The Remote Control function can be deactivated (programming mode P98, programming option 00), so that the Ctr message no longer appears at the start of the programme.

What should I do if the display texts appear in another language on a Miele washing machine?

The texts on the display of the washing machine/wash and dry combination appear in a foreign language.

The language is set to a foreign language.

Depending on the model, you can change the language using the programming functions or via the menu item 'Settings'.

The flag symbol on the display indicates the set language.

Wat betekent Gebruik “TwinDos” of voer in het menu “Onderhoud” het “TwinDos”-onderhoud uit op een Miele wasmachine?

The display of the washing machine shows 'Use “TwinDos” or perform the “TwinDos” maintenance in the 'Maintenance' menu.

TwinDos via compartment 1 and/or 2 has not been used for a long time. The washing machine has a cleaning programme for the TwinDos system. In this cleaning programme, the hoses in the washing machine are cleaned. For the cleaning, you need the cleaning reservoir 'TwinDos Care' or a refill reservoir.

Use TwinDos during one of the following washing programmes.

OR

Perform maintenance on TwinDos:

• Turn the programme selection switch to the Other programmes setting. 'Sportswear' will appear on the display.
• Touch the navigation arrows repeatedly until the 'Maintenance' menu appears.
• Confirm the setting with the sensor button OK.
• Touch the navigation arrows repeatedly until the 'Clean TwinDos' menu appears.
• Confirm the setting with the sensor button OK.
• Touch the navigation arrows repeatedly until the desired compartment is displayed.
• Confirm the setting with the sensor button OK. 'Start maintenance – no' will appear on the display.
• Touch the navigation arrows repeatedly until 'Start maintenance – yes' appears on the display.
• Confirm the setting with the sensor button OK.
• Follow the further instructions on the display.

Wat moet ik doen als het controlelampje rood kruis (hygiëne-info) brandt op een Miele wasmachine?

No washing programme with a temperature of more than 60 °C has been run for a long time.

Start the Cotton 90 °C programme with the Miele machine cleaner or a universal detergent.

The washing machine is being cleaned and no germs or odours are formed.

Wat betekent code Geen andere programmakeuze op een Miele wasmachine?

'No other programme selection' will appear on the washing machine display.

This display means that the position of the programme selector has changed after the programme has started. Once the programme has started, a wash programme cannot be changed.

Select the previously started programme again using the programme selector. The duration of the programme will be displayed.

​

• If you have the sensor button Start/Drum refill, turn the programme selector to the position  and then to the Cotton programme.
• If you do not have the sensor button Start/Drum refill, touch the sensor button Start/Stop.
• The display will show Programme cancelled or Cancel? yes.
• Press the sensor button OK.
• The washing machine will drain the wash water.
• The display will show Programme cancelled.
• Wait until the door is unlocked.
• Open the door.
• Close the door.
• Turn the programme selection switch to the desired programme.
• ​

More information can be found in the user manual.

Wat moet ik doen als Inw./Voorwas, Wassen, Spoelen of Spoelstop knippert op een Miele wasmachine?

The control lights for Pre-wash/Pre-wash, Washing, Rinsing or Rinse hold are flashing on the washing machine.

This is a technical fault, but first try this:

• Turn the programme selector to End.
• Turn off the washing machine.
• Switch the washing machine back on.
• Start a programme.

Contact We.repair if the fault persists or book a repair appointment online.

Wat betekent code  Kreukbeveiliging/Controleer dosering op een Miele wasmachine?

The display of the washing machine/wash-dry combination is flashing Crease protection/Check dosage.

A lot of foam was created during washing.

Use less detergent for the next wash. Follow the dosing instructions on the detergent packaging.

What does code noC mean on the display of a Miele washing machine?

The time display of the washing machine or tumble dryer shows noC when the MobileStart programme is selected.

The abbreviation noC stands for “no Connection.”

Miele@home is not installed.

• Connect the Miele appliance to a network. More information can be found in the user manual of your appliance. See the chapter “Initial Setup,” section “Miele@home.”

Miele@home is installed, but the Miele appliance is not receiving a WiFi signal.

Wat betekent Nulpuntinstelling niet mogelijk op een Miele wasmachine?

The display of the washing machine/wash-dry combination shows Zero point setting not possible. The door is closed.

Open the door and hold the Load/Dosing button until Zero point setting OK appears on the display.

What does "Enter PIN code" mean on a Miele washing machine?

The display of the washing machine shows Enter PIN code. The factory setting for the PIN codes for washing machines/wash-dry combinations is: 1 2 5.

The PIN code is active.

• Enter the PIN code and confirm it.
• Deactivate the PIN code if the prompt does not need to appear the next time it is turned on.
• More information can be found in the user manual.

Wat betekent Reactie waterproof op een Miele wasmachine?

The display of the washing machine shows Waterproof response.

The Miele water protection system has responded because water was detected due to a leak in the washing machine.

Follow these steps to remove the laundry:

• Turn off the water supply.
• Disconnect the washing machine from the power supply, the drain pump will stop running.
• Open the drum using the emergency release: open the drain pump door at the bottom left and unlock the door with a screwdriver.
• Open the door.
• Remove the laundry from the drum (note: only put your hand in the drum when it is no longer spinning)

Contact We.repair to remove the water and fix the leak.

What should I do if the Start button does not light up on a Miele washing machine?

The sensor Start button does not light up on the washing machine/wash-dry combination/dryer.

If the door is not closed properly, the programme cannot be started.

Press firmly against the side of the door where the lock is located.

Wat betekent Storing waterafvoer op een Miele wasmachine?

The water is not draining properly.

• The end of the drain hose is too high. Check that the maximum lift height of 1 m is not exceeded.
• Remove kinks or loops from the drain hose.

• Clean the lint filter and the drain pump:

  • Turn off the washing machine.
  • Open the flap for the drain pump (bottom left).
  • Place a container or bowl under the flap, e.g. a universal baking tray.
  • Loosen the filters until water flows out of the appliance.
  • Tighten the lint filters again to interrupt the water drainage.
  • If no more water is flowing out: completely unscrew the lint filters.
  • Thoroughly clean the filters.
  • Check if the pump blades can turn easily. Remove any foreign objects (buttons, coins, etc.) if necessary and clean the inside.
  • Reinsert the lint filters. Ensure that the lint filters are placed on the correct side.
  • Tighten the fluff filters properly so that no water can leak afterwards.
  • Close the flap for the drain pump.

Contact We.repair if the fault persists or book a repair appointment online.

Wat betekent Storing watertoevoer op een Miele wasmachine?

The water supply is blocked or obstructed.

• The tap is not turned on. End the wash programme. Turn on the tap. Select the programme and start it again.
• The filter in the water supply is contaminated. Clean the water supply filter in the plastic block on the supply hose. More information can be found in the user manual.
• Remove kinks or loops from the water supply hose.

There may still be a technical fault. Book a repair with We.repair.

Wat betekent Storing watertoevoer bij eerste ingebruikneming van een Miele wasmachine?

For safety reasons, spinning is not possible for the first use.

The factory-programmed spin lock prevents the washing machine from spinning before water supply has occurred.

To enable spinning, a wash programme without laundry and without detergent must be run, e.g. "Cotton 60 °C".

Wat betekent Storing watertoevoer huishoudwater op een Miele wasmachine?

The water supply is blocked or obstructed.

• The tap is not turned on. End the wash programme. Turn on the tap. Select the programme and start it again.
• The filter in the water supply is contaminated. Clean the water supply filter in the plastic block on the supply hose. More information can be found in the user manual.
• Remove kinks or loops from the water supply hose.

Wat betekent Storing watertoevoer warm water op een Miele wasmachine?

The water supply is blocked or obstructed.

• The tap is not turned on. End the wash programme. Turn on the tap. Select the programme and start it again.
• The filter in the water supply is contaminated. Clean the water supply filter in the plastic block on the supply hose. More information can be found in the user manual.
• Remove kinks or loops from the water supply hose.

What should I do if there are dashes '- - -' on the display and the indicator lights are flashing on a Miele washing machine?

The Miele water protection system has responded because water was detected due to a leak in the washing machine.

Follow these steps to remove the laundry:

• Turn off the water supply.
• Disconnect the washing machine from the power supply, the drain pump will stop running.
• Open the drum using the emergency release: open the drain pump door at the bottom left and unlock the door with a screwdriver.
• Open the door.
• Remove the laundry from the drum (note: only put your hand in the drum when it is no longer spinning)

Contact our service to remove the water and fix the leak.

Wat betekent TD bellen op een Miele wasmachine?

The display of the washing machine shows TD beeping and an audible signal sounds.

The drum lighting is not properly secured.

Check if the drum lighting is securely fastened:

• Switch off the washing machine and disconnect it from the power supply.
• Remove the opener from the inside of the detergent drawer panel.
• Insert the opener into the slot of the drum light.
• Turn the opener clockwise until you feel resistance and the light is securely in place.

Wat moet ik doen bij Technische storing. Neem contact op met Miele op een Miele wasmachine?

There is a technical fault.

First, try this: restart the programme.

Contact We.repair if the fault persists or book a repair appointment online.

What should I do if an "Exclamation Mark" and "Technical Fault" are flashing on a Miele washing machine?

Technical fault.

• Turn off the washing machine.
• If possible, disconnect the washing machine from the power supply by unplugging it.
• Reconnect the washing machine to the electricity supply.
• Turn on the washing machine.
• Restart the programme.
• Contact We.repair if the fault persists or book a repair appointment online.
• When the washing machine has a single-line display, press the sensor button V so that the fault code appears on the display. Provide the fault code to Miele when you contact them.

Wat betekent Vergrendeld. Code invoeren op een Miele wasmachine?

The display of the washing machine/wash-dry combination shows Locked. Enter code. The factory setting for the PIN codes for washing machines/wash-dry combinations is: 1 2 5.

The electronic lock is activated.

Enter the lock code and confirm it.

Deactivate the lock if the call does not need to appear the next time it is switched on, see the user manual.