Miele wasmachine faults

Typical problems with your Miele washing machine and their fault codes:

F1 – Temperature sensor defect → Replace sensor 

F2 – Rapid temperature rise → Check heating element 

F3 – Unrealistic temperature value → Check sensor or electronics 

F4 – Heating takes too long → Check heating element and water level 

F10 – No or insufficient water inlet → Open tap, clean filter 

F11 – Water drainage not working → Clean pump filter and drain hose 

F12 – Water valve not responding → Check electrical connection of valve 

F13 – Water inlet takes too long → Check water pressure and filters 

F14 – Circulation pump defect → Clean or replace pump 

F15 – Incorrect water amount → Check level sensor or water valve 

F16 – Drum sensor malfunction → Have motor or sensor checked 

F17 – Too much foam → Use less detergent 

F18 – Imbalance during spinning → Redistribute laundry, avoid small loads 

F19 – Insufficient heating → Check heating element 

F20 – Heating element defect → Replace element 

F21 – Heating takes too long → Check thermostat

F22 – Overheating heating → Stop program, let cool down 

F23 – Water level too high → Check pressure sensor or water valve 

F24 – Leak detection Waterproof active → Inspect bottom of appliance

F25 – Motor malfunction → Have motor checked 

F26 – Tachogenerator defect → Have sensor on motor checked 

F27 – No motor signal → Check wiring to motor 

F28 – Motor control electronics defect → Have electronics checked 

F29 – Motor blocked → Check drum and motor 

F31 – Motor safety activated → Reset appliance and reduce load 

F32 – Door lock not working → Check or replace lock 

F34 – Deur niet goed dicht → Sluit stevig of controleer rubbers

F35 – Control unit malfunction → Have circuit board checked 

F36 – Door does not open → Use emergency release 

F37 – Short circuit door lock → Replace lock module

F40 – Communication error modules → Reset machine, check wiring 

F42 – Unknown electronics error → Reset or contact service 

F43 – Motor overload → Reduce load, check motor 

F50 – Drum position not recognized → Check sensor or motor 

F51 – Washing movement malfunction → Check motor and control 

F53 – Motor speed not stable → Check carbon brushes (older models)) 

F56 – Excessive water intake → Check sensor or valve 

F58 – Worn carbon brushes → Replace carbon brushes 

F60 – Pressure sensor malfunction → Clean or replace sensor 

F63 – Software error → Have firmware reset 

F67 – Program data corrupt → Reprogram circuit board 

F68 – Relay works unexpectedly → Replace relay or circuit board 

F70 – Internal leakage → Check drip tray or bottom sensor 

F78 – Circulation pump blocked → Clean or replace pump 

F92 – Program communication error → Have software checked 

F93 – Detergent drawer detection error → Check sensor or drawer 

F94 – Dosing unit malfunction → Clean TwinDos or AutoDos 

F95 – Error in TwinDos system → Rinse or refill 

F96 – AutoDos motor malfunction → Have motor checked 

F97 – Incorrect module installed → Check settings

F98 – Voltage measurement error → Check electronic power supply 

F99 – Safety relay not working → Relay or circuit board defect 

FA0 – WLAN module malfunction → Restart module or reset WiFi

FA1 – Network configuration failed → Restore WiFi settings 

FA2 – WLAN connection error → Check router or signal 

FA3 – Miele@home error → Update app and restart 

FB0 – RFID reader not working → Check chip or contact 

FB1 – Dosing unit empty → Replace TwinDos cartridge 

FC0 – Incorrect configuration → Reprogramming required 

FC1 – Control malfunction → Check control panel 

FC2 – Display module malfunction → Check/replace module 

FD0 – Water valve remains open → Close water tap, call service 

FD1 – Too much water in drum → Check pressure sensor and valve 

FE0 – Systemic malfunction → Total reset or service required 

Waterproof – Leakage detected → Inspect machine for leaks 

Check inlet – Water not coming in → Tap open? Filter clean? 

Check drain – Drain not working → Clean filter and hose 

Call service – Serious error → Contact Miele service 

Drainage – Water drainage problem → Check pump/filter 

Overdose – Too much detergent → Use less, perform extra rinse 

Miele droogkast problemen

F01 – Probleem met temperatuurvoeler (NTC)
De temperatuurvoeler is defect of slecht aangesloten. Kan leiden tot onjuiste temperatuurregeling. → Laat controleren door We.repair

F02 – Oververhitting gedetecteerd
De droger is te warm geworden. Controleer het pluizenfilter, de condensor en de luchtcirculatie. Mogelijk thermische zekering geactiveerd.

F10 / F11 – Probleem met luchtcirculatie of motor
Slechte luchtstroom of motor draait niet goed. Reinig de filters, condensor en luchtkanalen.

F12 – Verwarmingssysteem werkt niet

Geen of onvoldoende warmte. Kan te maken hebben met verwarmingselement, relais of elektronica.

F15 – Probleem met vochtmeting (sensor)
De droger detecteert geen correcte vochtigheid. Controleer of de metalen strips binnenin schoon zijn (vaak rond de deuropening).

F53 – Probleem met motor of toerentalregeling
Kan duiden op een probleem met de aandrijving of de motorregelaar. We.repair kan hulp bieden.

F63 – Probleem met de elektronica / softwarefout
Reset de machine. Als het probleem blijft: contact opnemen met We.repair

F66 / F70 – Probleem met communicatie tussen modules (bijv. display en besturing)
Interne communicatieproblemen. Reset kan tijdelijk helpen, anders We.repair inschakelen.

Waterproof-fout – Lekkage of vochtprobleem binnenin
Dit activeert het beschermingssysteem van de droger. Stekker uit stopcontact, contacteer We.repair